Control arm, ball joint or bushing failure on the 2010 Dodge Caliber
When control arm, ball joint or bushing failure gets reported
Owners of the 2010 Dodge Caliber report control arm, ball joint or bushing failure at a median of 100,000 miles. A quarter of the reports come in before 90,000 miles and a quarter after 125,000 miles, from 20 reports that carried an odometer reading.
A part like this is normally expected to survive 108,000 miles. It is the 1st most-reported problem on this model year.
The mileage distribution
The reported range runs from 85,000 miles at the tenth percentile to 150,000 miles at the ninetieth, a spread of 66,296 miles across the middle 80% of reports.
A spread this wide points at use rather than design. Towing, climate, service history and city mileage all move a failure like this, so the median is a weak guide to any individual car.
5% of the dated reports were filed under 36,000 miles.
The whole distribution
| 10th | 25th | Median | 75th | 90th |
|---|---|---|---|---|
| 85,194 miles | 89,529 miles | 101,000 miles | 123,420 miles | 151,490 miles |
Read the 10th percentile as “one report in ten arrived this early”. Exact figures are shown in this table because it is the table of record; everywhere else on the site they are rounded to the precision the sample can carry.
What a percentile can and cannot tell you here
These five numbers describe the readings owners gave, in order. The median is the middle one: half the reports arrived below it. The 10th and 90th are the edges of the bulk of the distribution, and the distance between them is the part worth reading. A tight spread — say 70,000 to 95,000 miles — points at something that wears out on a schedule, and the schedule is knowable. A wide one, 20,000 to 190,000, points at a fault that hits some cars and never troubles others, which means the mileage on the listing in front of you tells you very little about your odds.
What these figures are not is a survival curve. Every reading here comes from a car whose owner filed a complaint, so the sample contains only failures: it cannot say what share of the fleet made it past 150,000 miles untouched, because those owners had nothing to report. Nor is the mileage the moment of failure — it is the odometer reading as recalled at the time of filing, which may be weeks later and is sometimes rounded to the nearest ten thousand by the person typing it.
Percentiles are shown at all only once 8 readings exist for the vehicle and mode. Below that the middle of a handful of numbers is noise wearing a decimal point, so the figures are withheld rather than dressed up.
What happens, and what it costs
Putting it right typically runs $400–$2,200 at an independent US shop. That range is an editorial estimate held in this site's failure-mode catalogue, not a figure from NHTSA, and it is a repair cost rather than a diagnosis cost.
The same failure on other years
The same failure is reported on 5 model years of this car. It shows up earliest on the 2009, at a median of 90,000 miles, and latest on the 2011 at 140,000 miles.
By volume the 2007 carries the most reports, with 170; the 2010 has 26. A mode that appears across most years of a model is usually a design choice rather than a bad batch.
If one year stands out to the left, that is the year to avoid; if the whole line sits at a similar mileage, this is wear rather than a defect in one production run.
Tick median reported mileage Solid middle half of reports Faint 10th to 90th percentile Colour how bad the failure is when it happens
What owners wrote
Verbatim from NHTSA complaint narratives, trimmed for length. The mileage is the one the owner gave.
Per my mechanic the ball joints need replaced. Having spoken with other caliber owners, it seems fairly unanimous that they have replaced or need to replace the ball joints on their cars not long after the manufacturer warranty expires. Further it is recommended to replace the whole lower control arm. *tr
Tl* the contact owns a 2010 dodge caliber. The contact stated that the rear adjustable control arms of the vehicle were welded to the vehicle and failed to adjust. As a result, the inside of the rear tires became worn. The vehicle was taken to the dealer where it was diagnosed that the tires needed to be replaced on three occasions, but the failure recurred. The vehicle was taken back to the dealer where the technician stated that the adjustable control arm needed to be replaced. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was 30,900.
I've had the arm bar and ball joint replaced twice in a year's time, which causes a grinding noise. I've had the brakes replaced three times along with rattle clips, in the last year, with no prevail in changing the noise nor high speed-braking oscillating. A caliper has also been replaced. While sitting at stop lights, the car unpredictably stalls-- I've tried to reproduce the setting to have the issue happen when a technician tests it, but it appears to happen unpredictably. The car has leaked from some entry point to cause the floor boards to be wet, and in the last year, the sun roof seems to be leaking as I have water pouring onto me from the front dome lightt. The water is causing mold, which is not beneficial to the family I drive with. Based on the NHTSA site and the thousands of youtube videos, these are pretty wildly known issues by dodge, despite the lack of complaints on these sites.
Also reported on the 2010 Dodge Caliber
Other engine problem
Airbag inflator rupture
Other electrical problem
Other speed control problem
Other powertrain problem
Headlight failure or clouding
How far this goes
Complaints are voluntary, so 26 is a floor and not a count of affected cars. Mileages are typed in by owners and cluster on round numbers. And the mode itself is assigned by software reading the complaint text, which is reliable in bulk and fallible one report at a time.
Questions this page answers
At what mileage does control arm, ball joint or bushing failure happen on the 2010 Dodge Caliber?
Across 20 owner reports that included an odometer reading, half were filed by 100,000 miles. A quarter were filed before 90,000 miles and a quarter after 125,000 miles. These are the mileages owners reported when they complained, not a prediction for any individual car.
How common is control arm, ball joint or bushing failure on the 2010 Dodge Caliber?
26 reports have been filed with NHTSA, about 0.4 per 1,000 vehicles. Complaints are voluntary, so this is a floor rather than a count of affected cars.
What this is and is not. These are the mileages at which owners chose to complain to a federal agency, which is not the same as the mileage at which the part fails on every car. It skews toward failures that happened outside warranty, cost real money, or frightened someone. It is still the only public dataset that carries failure mileage at all, and the shape of a few hundred readings is informative even when a single one is not. Methodology · JSON · this failure on other cars
Source Owner complaints and recall records published by the US National Highway Traffic Safety Administration, model years 1996–2027 Figures rebuilt Published by AtWhatMileage How every figure is computed